Skip to the page
Call us (909) 757-1103

Guide ยท Ontario

Why have I got no hot water?

No hot water usually traces to power, gas, a safety switch or a worn part, and the first checks take minutes. This page walks through each heater type and says where checking stops.

Updated

Troubleshooting flow: every tap cold points at the heater, one tap points at the fixture.

Start with one question: is the water cold at every tap, or only one? Cold everywhere points at the heater. Cold at a single faucet points at that faucet. When every tap runs cold, three suspects account for most calls. Energy is not reaching the heater, a safety cutoff has tripped, or a part inside has worn out. An element and a thermostat are the usual worn parts. This page builds on water heater repair and goes one step at a time. If the easy checks change nothing, Chaffey Pipe and Drain can arrange a local plumber. A quote request with your notes gets that started.

Is the cold at every tap, or only one?

Turn on the hot tap in the kitchen and in the shower. Cold in both means the heater is at fault. Cold in only one means that fixture needs a look: a failed cartridge, a clogged aerator or a crossed line can mimic a dead heater.

A middle result matters too. Hot at first, then cold, suggests a tank that is undersized, full of sediment or past its best. On electric units a dead lower element does the same thing. If it never gets truly hot, suspect a thermostat dialed low, or a tired element. Note which case you have before you call, because it shortens the diagnosis.

Where do you start with an electric water heater?

The breaker. A tripped breaker is described as a very common reason for no heat on A.O. Smith's own help page. Reset it once. A second trip means stop. Something is probably shorted in an element or the wiring, and resetting again over and over carries real risk.

Next, the red reset button, the energy cut-off, sitting near the upper thermostat. A.O. Smith says it trips on overheating and that repeated trips point to shorted elements or a faulty thermostat. Cut power at the panel before removing any cover, and let the tank cool first. Nervous around wiring? Hand it to a plumber. Our page on electric heater problems goes deeper.

What should you try on a gas unit before calling?

Check for a pilot flame, then confirm the valve on the gas line to the unit is turned on. A.O. Smith's page lists the pilot, the gas supply, a faulty control valve and a clogged burner or blocked air screen as the usual gas causes. If you smell gas, close the gas supply, leave, and call.

Gas water heater parts: gas valve, pilot, burner, thermostat and flue vent on a tank.

Gas smell? SoCalGas takes the report on 1-800-427-2200. Danger means 911. Relighting a pilot is something many manuals show, but follow your unit's label exactly, and quit if the flame keeps going out. A thermocouple, the small sensing rod, is a common failing part, and the page on a thermocouple replacement explains it. A related case is covered in the pilot is lit but the water is cold.

What stops a tankless heater from making hot water?

Candidates are a lost power supply, a shut gas valve, a clogged inlet screen, flow too weak to wake the unit, scale inside the heat exchanger, and an ignition fault that shows as an error code. Each maker publishes its own code list, so your manual decodes the display.

Some trade sources put the minimum flow needed to fire the burner at about half a gallon a minute, which varies by model, so a clogged aerator or a trickling tap can leave you cold. Manufacturers also call for periodic flushing, and hardness speeds scale. The 2025 city water report gives average hardness of 91 to 177 ppm by source, which makes scale a fair suspect locally. The guide to tankless no hot water continues from here.

Why are plumbers said to be against tankless water heaters?

Mostly because of what they add to a job, not because the units are bad. In my reading the usual complaints are purchase price, a larger gas feed, new venting, a flush every year in hard water, and owners who expect no upkeep at all. A well-matched unit with maintenance can serve a household well.

Plumbers are also asked to fix whatever model was installed, and some are cautious about brands they do not stock. Ask any contractor you consult to explain the reasoning for tank or tankless on your house, and request the gas line and venting costs in writing. The comparison page on tank versus tankless covers the trade-offs without a pitch.

Rental trouble: whose job is a dead water heater?

In California the landlord is responsible for a working hot water supply. Civil Code 1941.1, California's habitability law, counts a missing supply of running hot and cold water as a defect. Report it to the landlord or manager by message or letter, and note the date.

If you are the owner of the unit, the same troubleshooting applies. Shared boilers and central systems are handled by building management, and you cannot fix them from inside the apartment. Do not open gas appliances in a rental yourself. Report the outage, keep a copy of your message, and ask when the work is scheduled.

When does a cold shower become an emergency?

Not by itself, but a few signs make it urgent: a gas odor, a puddle under the tank, a relief valve venting steam or water, or scalding water at one tap and ice cold at another. Turn the heater's gas or power off, close the cold inlet if water is escaping, and call.

Seepage through the shell means the tank is done, and replacement is the sensible expectation. If you want same-day attention, see emergency water heater repair. Do not touch the pressure relief valve while the heater is running, because scalding water can shoot out.

What will it cost to fix?

That depends on what failed. A reset or dial adjustment is trivial next to a new element, and an element is small next to a new heater. Age matters here, since an old tank with a failing part may not be worth fixing.

No web page can stand in for a quote in writing from whoever inspects your unit. Ask for the cause in plain words, the price to repair, and the price to replace, side by side. The line items inside a replacement quote are listed under a new water heater's cost.

Ask for a written plumber quote

Fill this in and we'll arrange a local plumber specialist to come and price the job.

Needed so the business can price the job properly.

We earn a referral fee from the plumber who takes your job. You pay us nothing.

Common questions

Why does my hot water vanish after a minute?

On a tank heater, the supply may be small for your use, sediment may be insulating the burner or element, or a lower element or thermostat may have failed. On a tankless unit, a flow or scale problem can cause the same pattern. A plumber can sort out which.

Could a tripped breaker be the whole problem?

Yes. A.O. Smith's help page lists it first for electric heaters. Flip it back once. A second trip means call a plumber, because repeated resets can mask a shorted element, and live wiring is a bad place to experiment. A tripped breaker also tells you something is drawing too much current.

Can I relight a pilot light on my own?

Many manufacturers print the steps on the heater, and you should follow that label exactly. Back off the moment you smell gas, see the flame die again and again, or feel unsure about any step. A gas odor means everyone leaves first. The report goes to SoCalGas afterwards.

Fix the heater or swap it out?

It depends on the tank's age, which part failed and whether the tank itself leaks. Tanks that leak are replaced, not patched. A newer unit with one bad part is often worth repairing. Ask for what a repair would cost and what a new heater would cost, then weigh the two..

Who do I call, a plumber or a heating company?

A plumber handles water heaters, supply lines and valves. A heating company deals with furnaces and ducts, though some firms do both. Tell them it is a water heater when you call. Chaffey Pipe and Drain sends a local plumber and confirms the cost beforehand.

References