Skip to the page
Call us (909) 757-1103

Guide ยท Ontario

How to fix a two-handle leaky faucet

With separate hot and cold handles, each side has its own small valve, and the drip tells you which part failed. Read the symptom first, then open the right handle.

Updated

Side view of a compression faucet valve showing the stem, packing nut, O-ring, washer and brass seat.

Location of the water settles the diagnosis. Dripping from the spout implicates the washer or its seat; dampness at the handle implicates the sealing ring or loose packing. Close the valves under the basin, open the weeping side, exchange the part. More repairs of this kind are collected in the hub for faucets, drains and disposals.

Because each handle works its own valve, one side normally drips while the other is fine. Matching the symptom to the handle saves buying parts you do not need.

Before you start: is mine a compression faucet or a cartridge one?

Count the turns. Several full rotations to shut off means compression: the handle forces a rubber disc against a brass ring. A quarter or half turn means cartridge or ceramic disc. Compression valves drip more often, because the rubber is soft and wears first.

Compression valves turn up in older houses, including those near the Euclid Avenue historic district and postwar Montclair and Chino, while newer builds in Ontario Ranch and The Preserve more often have quarter-turn cartridges. Gather an adjustable wrench, two screwdrivers, a rag, plumber's grease and a small cup so tiny screws do not vanish down the drain. Stop the drain with a cloth.

How do I read the symptom?

Read the drip like a clue. Where water shows up, and whether the handle is open or closed, narrows the failed part to one or two candidates, so you can open the faucet with the right replacement already bought. The table below pairs each sight with its usual cause.

Symptom Probable culprit Replacement
Drip from the spout, handle closed Hard, worn or wrong-size washer, or a pitted seat Washer, then seat
Drip from the spout, quarter-turn handle Worn cartridge or scale between ceramic discs Cartridge
Moisture at the foot of the handle Dry or cracked O-ring, loose packing nut O-ring or packing
Handle stiff or squealing Dry stem, mineral crust Clean and grease

A table cannot replace looking: open the handle and judge the parts by eye. Scale is a regular feature here, since Ontario's 2025 water quality report puts hardness between 91 and 177 ppm on average depending on the source, and crusty white deposits on the stem point to mineral buildup rather than a failed part.

How do I rebuild a compression valve?

Close both stop valves below, then leave the faucet open until it stops running. Ease the decorative cap up, take out the screw underneath and slide the handle off. Turn the packing nut loose, lift out the stem, change the washer at its tip and look closely at the brass seat for scoring. Put everything back in reverse order and reopen the stops gradually.

A few details make the difference. Match the new washer to the old one in size and profile; a beveled one will not seal against a flat-faced stem. A light coat of silicone-safe grease goes on the stem threads and the O-ring. Nicks you can feel on the seat call for a dressing tool or seat wrench, or for replacing the valve. Do not crank the packing nut, because that squeezes the O-ring and the handle turns hard. The related single-lever version lives in repairing a one-lever faucet.

What changes when the faucet has cartridges?

Handle off, then free the cartridge by removing its retainer, and extract it straight upward, noticing which way its tabs face. Drop in an exact match facing the same way, or hot and cold will trade places. Cartridges are swapped whole, not repaired, and a near-match will leak.

An exploded cartridge faucet showing the retainer clip, cartridge tabs and matching slots in the valve body.

Take the spent cartridge to the supply counter, since lengths and splines differ. Ceramic discs seldom wear out, and a drip from one often means grit or scale between the discs, so rinse and clean the seals before spending money. A vinegar soak loosens mineral crust from parts that you reuse.

What if the drip survives a new washer?

Suspect the seat first: if it has eroded, it slices into any new washer. After that, consider a washer of the wrong diameter or one too stiff, and then a stem that is bent or scored. If a second rebuild fails, the valve body is probably corroded, and replacing the faucet makes more sense than another round.

A persistent drip has a cost. The EPA counts above 9,300 gallons of leakage per household each year, of which one faucet is only a small share. To gauge your own exposure, read whether a dripping faucet pushes up the bill and why a water bill can be so high. A general walkthrough for either design sits at fixing a dripping faucet.

Who should I call if it is beyond me?

A plumber is warranted when stop valves seize, a handle is frozen with corrosion, supply lines leak, the faucet sits in a wall at a tub or shower, or a stem snapped on the way out. A very old faucet is often replaced instead of rebuilt, and the shutoff valves may be replaced with it.

Replacement is a separate job, priced in the cost of installing a faucet, and shower valves have their own steps at a dripping shower faucet. Ask for a visit through the quote form, or look over the rest of the site on the home page.

Ask for a written plumber quote

Fill this in and we'll arrange a local plumber specialist to come and price the job.

Needed so the business can price the job properly.

We earn a referral fee from the plumber who takes your job. You pay us nothing.

Common questions

Per handle, how much time?

Count on thirty to sixty minutes with the supply closed and parts ready. A stuck stem, a rough seat or a second shopping run will lengthen it. A plumber usually handles both handles in a single call, which saves a second dismantling.

What do I settle with a plumber first?

Is the part price included? Will both handles and the stops be checked? Is the faucet worth saving at all? Agree on a figure before work. In California, a contractor license goes with permit work and with jobs from $1,000 up.

Should I stay home for it?

For your own repair, you will be there anyway. With a plumber, an adult should show the faucet and try it at the end. Clear out the cabinet below, with the stop valves reachable, because seized valves cause most delays.

References